SeedCode Support Forum

Please back up your file before making any changes.

If you haven't already, navigate to the "Settings" tab in the calendar sidebar and click "Account Settings". Click "Check For Updates". This button should change to "Install Update" and inform you that version 10.31 is available. Click "Install Update".

To update the necessary scripts, begin by downloading the latest version of DayBack here:

You should follow these instructions if you have done the embedded integration or the linking integration and you don't want to perform the integration all over again.

The Changes

Update the following script in your current DayBack File (Your file if you have done an embedded integration), but don't delete the script itself. Rather, use the "Select All" command to select and delete the entire contents of each script, then copy/paste the updated contents of the script from the new version of DayBack into the corresponding script in your DayBack file. You may get an error when opening both files at the same time. This is expected and you can just say "OK" to those errors before continuing. Here is the script that needs to be updated this way:

"Check for FMP URL"

The following scripts will need individual script steps added to them. As in the previous step you can copy the script steps from the new DayBack file you downloaded. Then paste them into your script. For these you will not need to delete any existing script steps, just add the new ones as pictured below.

"Query Events From WebViewer"


"Load Calendar Layout"


The following script will need to have script steps removed. So please highlight the script steps as shown in the image below and remove them from the script.

"Upon Opening" (Delete the Perform Script "Check for FMP URL" script step)
Note for SeedCode Complete: This script is called "Upon Opening DayBack" in SeedCode Complete.


Finishing Up:
Close the new DayBack file you used to copy the script contents from.
Change the build number recorded in the database. Navigate to "File -> Manage -> Database" then go to the "CalendarInterface" table. Change the "BuildNumberCalc" calculation to read "10.31". Click "OK" to save those changes.

Then please run the "Upon Opening" script in your file. This will ensure all of the new settings load properly and the calendar loads with the correct data.

That's it, enjoy DayBack 10.31.

Hi Tanner,

I am a bit confused with the last step of the instructions: it says that the script Upon Opening needs to be amended, but I have 3 Upon Opening Script. I have SeedCodeComplete.
Upon Opening
Upon Opening DayBack
Upon Opening WebDirect

So I looked at the Upon Opening DayBack and figured this is the one that I need to amend, but I noted, that the version history mentioned that in version 9.69 a change was made, but I don't have this change.
I went back to all the update instructions, but I can't find any instructions on updating to 9.69. Did I miss something here?

There are a couple of script steps different in my version. Attached screenshots, I marked the different lines with the blue marker.

Please could you kindly advise what I should do.

Thanking you in advance.

Kind regards

Regine

Hi Regine,

Thanks for the screenshots and details. I'll dive into this on my end and get back to you with more info.

Regards,

KC

Hi Regine,

The update that is commented as "9.69 FBz 39557" was actually applied in the instructions for 9.72 here: viewtopic.php?f=40&t=4286&p=11892#p11892

This update added the "Check for FMP URL" script step to the "Upon Opening" script. It was applied in our release of Complete, but we must have forgotten to add it to the comments section, but it doesn't look like you missed applying anything.

When applying DayBack changes that apply to the "Upon Opening" script, you'll want to modify the "Upon Opening DayBack" script as you predicted.

For this step, you'll just need to remove the "Check for FMP URL" script step and you should be all good.

Hope that helps!

KC

HI KC,

again apologies for the delay. Since I don't get notifications when the post is updated, I keep forgetting about it.

One last question here:
In the Upon Opening DayBack script I have a script step, that isn't in the original file:
Perform Script [Specified:From list; "Create Selector Rows"; Parameter: ] (see attached screenshot)

Is this related to my SeedCodeComplete verion? Or should I delete this step?

Thanks

Kind regards

Regine

Yes, that's related to SeedCode Complete.

No, you should not delete that =)

Best,

John

Thanks John!